CoffMeter W1 Complete Guide

Part 1: The device

CoffMeter W1 measures the water activity of green and roasted coffee in about 2 minutes, and shows the ambient temperature, humidity, air pressure and altitude it was measured at. Connect it to CoffeeOS to record each reading with the coffee it came from.

CoffMeter W1 on a tray of green coffee.
CoffMeter W1 on a tray of green coffee.

What water activity measures

Moisture is how much water a bean contains. Water activity is how free that water is to move around and react with its environment, on a scale from 0 to 1. Two lots with the same moisture can read different water activity. Water activity is the one that predicts how a lot ages in storage.

Reference points: below 0.60 aw, nothing grows. SCA guidance puts green coffee at 0.45 to 0.55 aw, with 0.65 as the upper limit for storage. These figures are guidance for green coffee.

For moisture and density, pair it with CoffMeter M1. For all three plus screen size and roast color in one device, see Omix Plus.

What’s in the box

coffmeter_w1_fig_box

Main unit
Base and sample tray
Saturated salt solution bottle
USB-C charging cable
Spoon
Tool kit
User manual with warranty card
Product QR code card
Certificate of conformity

There is no power adapter in the box. Use any USB adapter rated 5 V / 1 A.

Know your CoffMeter W1

The main unit seated on the base.
The main unit seated on the base.

Main unit - the top half, with the screen and the button. It covers the sample container for every test and calibration.

Touchscreen - 2.31-inch display. It shows the result, the test curve, the conditions in the room, and the Test and Calibrate buttons.

Button - the round button below the screen. It powers the device on and off and starts a test.

Base and sample tray - the bottom half. The sample tray is the container the coffee or calibration solution goes in. The base holds it magnetically, and the container floats slightly until you turn it into place.

Saturated salt solution bottle - the bottle you mix the calibration solution in. It is marked with a salt line and a water line, and it stores the solution between calibrations.

Charging port - USB-C, on the bottom of the device.

The button and swipes

ActionWhat it does
Press (powered off)Powers on.
Short press (powered on)Goes to the test screen and starts a test, from any screen.
Long press (powered on)Powers off.
Swipe left to rightOn the home screen, opens Settings. On any other page, goes back one page.
Swipe right to left on the test screenOpens the history of saved results.

The test screen

coffmeter_w1_fig_screen
On screenWhat it shows
1 Sample numberAssigned automatically when a test finishes.
2 App connectionWhite when connected to CoffeeOS, gray when not.
3 BatteryCharge it when the level is low.
4 Test curveHow the water activity reading changes over the course of one test.
5 ResultThe water activity, in aw.
6 TestStarts a test.
7 CalibrateStarts calibration.
8 ConditionsAmbient temperature, humidity, air pressure and altitude.

Settings

Swipe from left to right on the home screen to open Settings.

SettingWhat it does
Device InfoSerial number and firmware version, plus a QR code to download CoffeeOS.
Bluetooth ConnectionOn by default. Leave it on to connect to CoffeeOS.
Status Bar (Testing Page)Shows or hides the battery and connection icons at the top of the test screen.
Temperature Unit°C or °F.
LanguageEnglish, Japanese or Simplified Chinese.
Display BrightnessScreen brightness.
Auto-OffNever, 3, 5 or 10 minutes.
Factory ResetTap, then press and slide to the right. The device resets and powers off, and all saved results and settings are cleared.

Calibration

Calibration standardizes the reading against a saturated salt solution of known water activity. Calibrate once a day before you start testing. A correct calibration reads between 0.745 and 0.755 aw.

Make the solution 1 hour ahead. It needs that long to saturate fully. The solution can be reused, so make it in advance and keep it in the sealed bottle. Replace it once a month, and make a new batch if it has been left open to the air or in direct sunlight.

Mix the solution and let it stand
1. Mix the solution and let it stand
Add salt to the NaCl line on the bottle, then add warm water up to the Water line. Cap it, shake well, and leave it for 1 hour. Some salt staying undissolved at the bottom is normal. It means the solution is saturated.

With the solution ready, calibrate:

Check the container
1. Check the container
Clean out anything left in the sample container.
Pour in the solution
2. Pour in the solution
Pour the solution in, undissolved salt included, until the bottom of the container is covered. A little more or less does not change the result.
Seat the container
3. Seat the container
Place the container on the base and turn it slightly clockwise until it sits in place. If it floats, hold the edge and turn it clockwise until it drops into position.
Close the main unit
4. Close the main unit
Set the main unit on top. Tap Calibrate on the home screen, follow the on-screen prompt, and start. Calibration takes about 5 minutes.
Release and store
5. Release and store
Press down on the edge of the container and turn it counterclockwise. It pops up and floats so you can lift it out. Pour the solution back into the bottle and seal it for next time.

Take a reading

A test takes about 2 minutes when the sample and the device are at the same temperature. Let freshly roasted coffee cool to room temperature before you test it, and test in a room between 40 and 60% humidity.

Add the sample
1. Add the sample
Spoon in just enough beans to cover the bottom of the container. A little more or less does not change the result.
Seat the container and close the unit
2. Seat the container and close the unit
Turn the container clockwise into place on the base, then set the main unit on top.
Start the test
3. Start the test
Tap Test on the screen, or press the button. Tap Test again if you need to stop partway through.
Empty and brush the container
4. Empty and brush the container
When the result appears, remove the sample and brush the container clean with a soft brush, ready for the next one.

History: CoffMeter W1 saves up to 500 results. Swipe from right to left on the test screen to see them.

Don’t leave a sample sitting: empty the container as soon as a test or calibration is finished.

Keep it clean

After each use, brush any coffee residue out of the container and off the main unit. Residue left behind affects the next reading. Use a soft brush or cloth, never steel wool or anything hard.

Charging and storage

A full charge takes about 3.5 hours and lasts about 8 hours of continuous use. If you are putting CoffMeter W1 away for a while, charge it fully first and top it up from time to time. A battery stored empty can damage the device.

Specifications

SpecificationValue
SamplesGreen coffee, roasted coffee
Measurement range0.05 to 0.99 aw
Accuracy±0.02 aw
Resolution0.001 aw
Test timeAbout 2 minutes (sample and device at the same temperature, 40 to 60% humidity)
Calibration timeAbout 5 minutes
Operating temperature0 to 45 °C
Operating humidity40 to 60% RH
Size76 mm diameter × 52 mm
Screen2.31-inch TFT
Battery1500 mAh, about 8 hours of continuous use, about 3.5 hours to charge
ChargingUSB-C, 5 V / 1 A (adapter not included)
Saved results500
Also showsAmbient temperature, humidity, air pressure and altitude

Part 2: CoffMeter W1 in CoffeeOS

CoffeeOS is free, with no purchase necessary. Connect CoffMeter W1 to import water activity into Bean Manager, where it is saved with the green or roasted coffee you measured.

Connect

Download CoffeeOS and allow Bluetooth, location and every permission it asks for. Check that Bluetooth Connection is on in the device Settings.

First connection
1. First connection
Power on CoffMeter W1 and open CoffeeOS on the Tools tab. A connection prompt appears. Tap Connect.
After that
2. After that
Power on the device and open CoffeeOS. It reconnects automatically.

If the prompt doesn’t appear, go to Me, then Device Center, and connect from there.

Update the firmware

New firmware adds features and improves stability, so check for updates regularly. With CoffMeter W1 connected, go to Me, then Device Center, and tap CoffMeter W1. Update over Wi-Fi or a mobile hotspot for a more stable download.

Add water activity to a coffee

Open Bean Manager and choose the Green or Roasted tab. Tap + to add a new coffee, or open one you already logged and tap Edit.

Turn on Water Activity
1. Turn on Water Activity
In Bean Qualities, open Edit Fields and switch on Water Activity, along with anything else you plan to record.
Import from CoffMeter W1
2. Import from CoffMeter W1
Tap Import on Bean Qualities, choose Device Auto-Fill, and select CoffMeter W1.
Run the test
3. Run the test
With the sample in place, press Test on CoffMeter W1. When the test finishes, the result is imported into the Water Activity field.

Save the entry. CoffMeter M1 imports moisture and density, and CoffMeter A1 imports roast color, into the same coffee the same way.

Share the data

Open the coffee in Bean Manager and share it from the menu at the top. The person you send it to opens it in their own CoffeeOS, with the water activity and every other reading you saved. For a producer, that means buyers can see the readings behind a lot before it ships.