CoffMeter M1 Complete Guide

Part 1: The device

CoffMeter M1 measures moisture content, density and sample temperature for green beans, roasted beans, parchment and dried cherries, in two seconds or less. Producers can check parchment and dried cherries, and roasters can check a green lot before it goes in the roaster, where moisture and density help you set your charge temperature. Import results into CoffeeOS to keep them with the coffee you measured.

What’s in the box

coffmeter_m1_box

Main unit
Bean Sweeper
Brush
USB-C charging cable
Toolbox
Manual, with warranty card
Product QR code card

There is no power adapter in the box. Any USB adapter rated 5 V / 0.8 A works.

Know your CoffMeter M1

CoffMeter M1 from the front and from the back.
CoffMeter M1 from the front and from the back.

Main unit - the body and the chamber on top, where the sample goes. Lift the device by supporting the bottom with your hand, never by the chamber.

Touch screen - shows your results, the menu and the settings.

Button - below the screen. Press and hold to power on.

Charging port - USB-C, at the bottom of the device.

Bean Sweeper - sits on the chamber while you pour in the sample. Turn it in the direction of the arrow to level the sample, then lift it off before testing.

Before you power on

M1 initializes density with whatever is in the chamber when it powers on. Start every session on a stable, flat surface with the chamber empty and nothing touching the device.

Nothing touching the device, an empty chamber, and a hand under the bottom when you move it.
Nothing touching the device, an empty chamber, and a hand under the bottom when you move it.

The home screen

coffmeter_m1_screen
On screenWhat it does
1 Sample typeTap to choose green beans, roasted beans, parchment or dried cherries.
2 Record numberAssigned to each result when a test finishes.
3 CoffeeOS connectionWhite when connected, gray when not.
4 MoistureMoisture content, in %.
5 DensityDensity, in g/L.
6 Sample temperatureThe temperature of the sample in the chamber.
7 ZeroZeroes the weight. Empty the chamber before you tap it.
8 TestMeasures moisture, density and sample temperature together.
9 Swipe rightShows the menu. On any other screen, swiping right takes you back.
10 Swipe leftShows your measurement history.

Menu and settings

Swipe right on the home screen for the menu: Test, Calibrate, Settings and History.

Swipe right from the home screen to reach the menu.
Swipe right from the home screen to reach the menu.
coffmeter_m1_settings
SettingWhat it does
BluetoothOn by default. Keep it on to connect to CoffeeOS.
Temperature Unit°C or °F.
LanguageEnglish, Simplified Chinese, Traditional Chinese, Japanese, Korean and Spanish.
Screen BrightnessAdjust to suit the room.
Auto-Power offNever, 3, 5 or 10 minutes.
Device infoSerial number and firmware version, plus a QR code for connecting to CoffeeOS.
Factory ResetPress and hold, then swipe right. Clears every stored result and setting.

Calibration material: earlier units shipped with a pack of calibration material. A firmware update has since improved the calibration logic so the material isn’t needed, and new units no longer include it. If you have an older unit, update it to the latest firmware and use it the same way.

Take a reading

Power on with the chamber empty
1. Power on with the chamber empty
Place M1 on a flat surface, empty the chamber and press the button.
Choose the sample type
2. Choose the sample type
Tap the sample type at the top left and pick green beans, roasted beans, parchment or dried cherries. If anything has been in the chamber since power on, empty it and tap Zero.
Pour in the sample
3. Pour in the sample
Set the Bean Sweeper on the chamber and pour the sample in through it.
Level it, then remove the Bean Sweeper
4. Level it, then remove the Bean Sweeper
Turn the Bean Sweeper in the direction of the arrow until the sample fills every recess and the surface is flat. Scrape it level without pressing down. Lift the Bean Sweeper off before testing, since leaving it on changes the result.
Test
5. Test
Tap Test. Moisture, density and sample temperature appear together.
Brush out the chamber
6. Brush out the chamber
Empty the chamber and clean it with the brush before the next sample.

Repeat readings: on the same beans, density should agree within ±2 g/L from one fill to the next. To retest a sample you have poured out, tap Zero with the chamber empty before you pour it back in.

Keep it clean

coffmeter_m1_clean

Residue in the chamber or on the body affects the next reading, so brush both out after use. Never use steel wool or anything hard on the chamber or the body.

Before putting M1 away for a long time, charge it fully, and recharge it every so often while it is stored. A battery left flat can damage the hardware.

When something looks wrong

What you seeWhat to do
“Weight too low”, NA, or a result that looks wrongRemove the Bean Sweeper, empty the chamber, tap Zero and test again.
Density varies between fills of the same beansPour through the Bean Sweeper along the arrow, fill every recess, scrape flat without pressing, and remove the Bean Sweeper before testing. Tap Zero with the chamber empty before each refill.
CoffeeOS can’t find M1Check that Bluetooth is on in M1’s settings, and that CoffeeOS has Bluetooth, location and every other permission it asks for on your phone.
Won’t power onCharge it.
White screen, an error code, an unresponsive button, or density still outside specification after correct fillingEmail service@digitizefluid.com with a description, a video of the problem and the serial number, which is on the bottom of the unit.

Specifications

ItemValue
MeasuresMoisture content, density, sample temperature
Sample typesGreen beans, roasted beans, parchment, dried cherries
Moisture contentRange 0 to 50%, accuracy ±0.2%, resolution 0.1%
DensityRange 0 to 1200 g/L, accuracy ±1 g/L, resolution 1 g/L
Test time2 seconds or less for moisture and density
Dimensions135 × 83 × 83.7 mm
Weight445 g
Screen2.31-inch HD touch screen
Battery2500 mAh lithium, 10 hours of continuous use, 4 hours to charge
Stored records500
Operating temperature0 to 45 °C
ChargingUSB-C, 5 V / 0.8 A

Part 2: CoffMeter M1 in CoffeeOS

CoffeeOS is free, with no purchase necessary. Connect M1, import moisture and density into Bean Manager, and keep every reading linked to the coffee you measured.

Connect

Download CoffeeOS and allow Bluetooth, location and every other permission it asks for. Power on M1 and open CoffeeOS. A connection prompt appears; tap Connect. From then on, M1 reconnects automatically whenever you power it on with CoffeeOS open.

Power on M1, open CoffeeOS, and tap Connect.
Power on M1, open CoffeeOS, and tap Connect.

If the prompt doesn’t appear, swipe right on M1’s home screen, open Settings, then Device info. Tap the scan icon at the top right of CoffeeOS and scan the QR code on M1’s screen.

Add moisture and density to a coffee

Bean Manager in CoffeeOS holds a record for every coffee you buy, roast or brew. Readings from M1 go into that record, so the moisture and density of a lot are there when you plan the roast or compare it with the next delivery.

Open or create the coffee
1. Open or create the coffee
In Bean Manager, choose the Green Beans or Roasted Beans tab. Open an existing coffee, or tap + to add a new one.
Turn on the fields
2. Turn on the fields
In Bean Qualities, tap Edit Fields and switch on Moisture and Bulk Density.

Tap Import in Bean Qualities, choose Device Auto-Fill and select CoffMeter M1. Set the sample type, prepare the sample in the chamber the same way as on the device, and tap Test. Moisture and Bulk Density are imported into the record. Save.

M1 covers moisture and density. Water activity comes from CoffMeter W1 and roast color from CoffMeter A1, or you can type a value from any other meter by hand.